D-Link DIR-868L Router Migration and Upgrade - www.hardwarezone.com.my

HWZ Forums

Login Register FAQ Mark Forums Read
HWM Malaysia on Facebook

D-Link DIR-868L Router Migration and Upgrade

Reply
 
Thread Tools
Old 21-12-2019, 06:09 PM   #1
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
D-Link DIR-868L Router Migration and Upgrade

Dear forum members,

I am new to this forum.

Recently, i bought D-Link DIR-868L router during Shoppee 11.11 sale for a good price.

I would like share my experience in migrating the router to DD-WRT firmware and Tomato firmware.

Also, I am able to go back to D-Link firmware after i tested DD-WRT and Tomato firmwares.

Flashing other than factory firmware into routers is not an easy thing.

You need patience and clear mind, so that you can see what went wrong and take necessary steps to overcome the problems.

Regards,
Iskandar
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:14 PM   #2
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
This guide was developed from various online resources and personal experience on D-Link 868L A1.
Credits are due to all contributions, direct or indirect.
Only applicable to D-Link DIR-868L with HW A1 and FW 1.22SHC.
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:15 PM   #3
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Step 1: Downgrade DIR-868L factory firmware to FW1.00SHC

• Bear in mind that it is not recommended to install third-party firmware such as DD-WRT or Tomato though D-Link normal firmware upgrade. You will encounter all kind of problems. Something that you really want to avoid.
• You need to perform migration at Recovery Mode. Please refer to the steps at Recovery Mode, last section of the document.
• First, you need to downgrade from your existing firmware (e.g. FW1.22SHC) to FW1.00SHC. This is important for successful migration to DD-WRT or Tomato firmware.
• Download FW1.00SHC firmware from D-Link Singapore website https://www.dlink.com.sg/dir-868l/#firmware.
• Unplug all cables (incl. power cable) from the router.
• Connect the router to the PC using one of the 4 switch ports
• Set computer IP address to 192.168.0.2 and use 255.255.255.0 as the Subnet mask.
• Power-on the router while pushing a paperclip to the hidden reset button located at the bottom of the device for a few seconds.
• When the Power LED starts blinking, release the reset button.
• Use Mozilla FireFox browser and navigate to http://192.168.0.1. Other browsers will give you problems.
• You will see a text-based firmware update page where you can select the firmware file you want to upload.
• Upload the FW1.00SHC firmware, when completed the router should report to reboot.
• The router should now be running FW1.00SHC firmware and accessible on the default address. (http://192.168.0.1). Default user is admin and no password i.e. blank
• The router is ready to be migrated to DD-WRT firmware.
• It is important to note that it is necessary to migrate the router to DD-WRT before you migrate to Tomato firmware.
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:17 PM   #4
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Step 2A: Migrate to DD-WRT firmware

• First, you need to download DD-WRT firmware.
• DD-WRT version r25974 was used with great success repeatedly and on three separate units.
• Download the r25974 files here. ftp://ftp.dd-wrt.com/betas/2015/01-20-2015-r25974/
• Download two files factory-to-ddwrt.bin and dir868a-webflash.bin.
• First, flash the factory-to-ddwrt.bin file using the D-Link router’s firmware upgrade page.
• The process will take up a few minutes. Once successfully flashed your router will reboot.
• Next, go to the router page (default is 192.168.1.1)
• Using the D-Link router’s firmware upgrade page, flash second file, dir868-webflash.bin.
• The router will reboot once again.
• You should see DD-WRT and will be asked to enter new user and new password.
• I suggest admin and admin, repectively. You can change them when you complete the whole migration process.
• At this point you have a choice to updrade to newer DD-WRT firmware version (Step 2B) or upgrade to Tomato firmware (Step 2C).
• The following link may help you to decide to choose between DD-WRT or Tomato firmware. https://techstorify.com/dd-wrt-vs-to...uter-firmware/
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:17 PM   #5
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Step 2B: Upgrade to newer DD-WRT firmware

• Download the latest DD-WRT firmware ftp://ftp.dd-wrt.com/betas/
• Choose 2019 folder.
• Latest is r41686 ftp://ftp.dd-wrt.com/betas/2019/12-1...-dir868l-reva/
• Download the dir868a-webflash.bin file.
• Go to Administration -> Firmware Upgrade and browse to select the file.
• Then flash the dir868a-webflash.bin file with Reset to Default Settings.
• As usual the process could take up to 3 minutes.
• Once complete, the new DD-WRT firmware should boot up.
• Right after this, go to Administration -> Configuration ->Restore Default Configuration and choose Erase all data in NVRAM memory (thorough) option.
• Click OK button.
• This will take a few more minutes. Once done, you are all set!
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:18 PM   #6
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Step 2C: Migrate to Tomato firmware

• Download the latest Tomato by Shibby firmware.
• Latest is version is 140. http://tomato.groov.pl/download/K26ARM/140-MultiWAN/
• Unzip the file.
• Go to Administration -> Firmware Upgrade and browse to select the file.
• Then flash the tomato-DIR868L-ARM--140-special.trx file with Reset to Default Settings.
• As usual the process could take up to 3 minutes.
• Once complete, the new Tomato firmware should boot up.
• Right after this, go to Administration -> Configuration ->Restore Default Configuration and choose Erase all data in NVRAM memory (thorough) option.
• Click OK button.
• This will take a few more minutes. Once done, you are all set!
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:19 PM   #7
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Step 2D: Optional upgrade to Advanced Tomato firmware

• This is an optional step.
• Advanced Tomato present a more pleasant GUI that some of us would appreciate.
• Download the latest Advanced Tomato firmware.
• Latest is version is 3.5-140. https://advancedtomato.com/downloads/router/dir868l
• Unzip the file.
• Go to Administration -> Firmware Upgrade and browse to select the file.
• Then flash the tomato-DIR868L-AT-ARM-3.5-140-special.trx file with Reset to Default Settings.
• As usual the process could take up to 3 minutes.
• Once complete, the new Tomato firmware should boot up.
• Right after this, go to Administration -> Configuration ->Restore Default Configuration and choose Erase all data in NVRAM memory (thorough) option.
• Click OK button.
• This will take a few more minutes. Once done, you are all set!
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:23 PM   #8
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Recovery Mode:
D-Link DIR-868L provides an easy way to recover using Recovery Mode (Also a useful and a recommended way to install third-party firmware)
• When the Power LED keeps blinking on boot, the router has entered the recovery mode.
• This usually happens when flashing a firmware went wrong, or the configuration has been corrupted.
• It is also possible to (force) boot into recovery mode to restore a soft-bricked router or flashing back to the factory firmware.
• Download the latest available firmware on the official D-Link website of the router revision. https://www.dlink.com.sg/dir-868l/#firmware
• Unplug all cables (incl. power cable) from the router
• Connect the router to the PC using one of the 4 switch ports
• Set the PC TCP/IPv4 address to 192.168.0.2 and use 255.255.255.0 as the Subnet mask
• Power-on the router while pushing a paperclip to the hidden reset button located at the bottom of the device for a few seconds.
• When the Power LED starts blinking, release the reset button
• Use Mozilla FireFox browser and navigate to http://192.168.0.1. Other browser will give you problems.
• Upload the D-Link firmware, when completed the router should report to reboot.
• The router should now be running stock D-Link firmware and accessible on the default address. (http://192.168.0.1).
• Please note that if you encounter problems going back to the latest stock D-Link firmware, it is suggested to start with an early firmware e.g. FW1.03 and work your way up until the latest.
• Each time you need to reset to factory defaults to clear the NVRAM memory of the router, before you upgrade to a newer firmware.
• The last step seems to be necessary when you are upgrading from FW110 to FW122, if you encounter a warning that size of the firmware is too big.
misk2020 is offline   Reply With Quote
Old 21-12-2019, 06:24 PM   #9
misk2020
Junior Member
 
Join Date: Dec 2019
Posts: 10
Well. I hope this guide help individuals wanted to migrate their DIR-868L to DD-WRT or Tomato firmware with minimal problems.
misk2020 is offline   Reply With Quote
Old 04-02-2020, 01:52 PM   #10
radhikashetty
Junior Member
 
Join Date: Feb 2020
Posts: 1
Great Thread
Electrical Design Course in Delhi
radhikashetty is offline   Reply With Quote
Old 08-07-2020, 07:37 AM   #11
hyruxoji
Junior Member
 
Join Date: Jul 2020
Posts: 1
You can also listen music premium from youtube

Youtube Music Mod Apk allows you to listen all premium music for free. Music lovers all over the world love to use premium music from Youtube to listen to songs and know that you are one of them too. Because the average person can also listen to Youtube Music APK songs. But music lovers just want to download Youtube Music Premium MOD APK. Well, it doesn't matter if you love music or not. Our mission is to introduce you to the Mod app, so we are here today with APK Youtube Music Premium Cracked for you.

Let me tell you, we offer free premium apps here every day. It is also useful for everyone. Here we also offer Mod on demand. So, if you want a hacking or hacking version of any APK APK, you can ask us by comment. You will only find this on tricksndtips

This is the age of technology. Here the person wants to do many things at the same time. This is also called multitasking. We want to listen to songs while we eat. People want to watch videos while talking. All this is possible at the time of the day. Because if you have a smartphone and an internet connection it works. So, with the help of Youtube Music Premium APK, you can listen to songs while doing any work.
hyruxoji is offline   Reply With Quote
Old 21-07-2020, 12:21 AM   #12
gtalovers
Junior Member
 
Join Date: Jul 2020
Posts: 1
great

great information. Im lookng this.
regards
technologywell
__________________
https://technologywell.com/gta-vice-city-apk/
gtalovers is offline   Reply With Quote
Old 24-08-2020, 08:43 PM   #13
alltechcloud
Junior Member
 
Join Date: Aug 2020
Posts: 1
Dear forum members,

I am new to this forum.

Recently, i bought D-Link DIR-868L router during Shoppee 11.11 sale for a good price.

I would like share my experience in migrating the router to DD-WRT firmware and Tomato firmware.

Also, I am able to go back to D-Link firmware after i tested DD-WRT and Tomato firmwares.

Flashing other than factory firmware into routers is not an easy thing.

You need patience and clear mind, so that you can see what went wrong and take necessary steps to overcome the problems.

Regards,
Iskandar
Enjoy free premium Youtube Music Account. If you music lover and looking for the best free and premium account. Just use the Youtube premium Music apk to listen the music. A Youtube music premium account is used by around the world.


https://alltechcloud.com/youtube-premium-apk/

Get Free Tech Reviews, Premium Account like Netflix, Youtube Music, Hotstar, Mod, APK
https://alltechcloud.com/youtube-pre...flix-accounts/
alltechcloud is offline   Reply With Quote
Old 25-09-2020, 02:03 PM   #14
covertnoob
Junior Member
 
Join Date: Sep 2020
Posts: 1
Thanks for such awesome posts. Zooqle Proxy

Also Download Zee5 App for PC without Bluestacks
covertnoob is offline   Reply With Quote
Reply


Thread Tools

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump